Gamo Air Rifle can't shoot straight.

[Moveon]

OK, I've been fooling around with this guy and rifle scope from Gamo all summer.

I ordered a scope stop from Gamo and got it in the mail today. So I added it to the back scope base ring. This base also has a vertical pin type scope stop that fits into a hole that was drilled into the top of the barrel.

Once I got the scope mounted the other day (for the fourth or fifth time) and put the Blue Thread lock on all the new screws that I got from EBN I was able to let the thread lock material dry for 24 hours. Do today at 2 pm the 24 hour period of time had elapsed.

Today was calm and I set up my targets at 20 yards and 25 yards respectively. I was able to install the new scope stop behind the ring base that came with the rifle and the original scope. It took me a while to get it to grabs the 3/8" groves but I got it tightened in place using a 2.5 MM Hex head Allen wrench. Note: the scope stop didn't come with any tools to install it. I was lucky that I already had the right sized metric Allen wrench.

I took the gun out in the back yard and started by using a laser bore sighter and the scope was almost right on the money at 10 yards.

I fired a few rounds in to the target at 25 yards and noticed that differnet ammo shot differently. I 'd zero the scope in on the 20 yard target and then when I changed from a Lead Red Point type pellet to the Gamo Gold Raptor pellet the shots placements were different. But they were precise. The groups stayed together which tells me that the rifle scope is staying where I put it and not moving ... yet!

I was able to get some Gamo Platinum pellets to group well and on the target bulls eye.

Here is a shot of the last 4 rounds after I adjusted the scope windage and elevation knobs to bring the scope on target.

Opps: the target is upside down. I didn't edit this before posting. Sorry. The last shot was a little low as I let my next door neighbor kid shoot the last three shots. My first shot was right on target in the middle of the orange circle. He put two more on the bulls eye. The last shot was actually low because the other kid came over to see what was going on and one of the little brats was standing behind the shooter and bugging him.

By this time 6 other little kids showed up to see what we were doing so I figured it was time to put the gun away. LOL.

I'll not say anything else until I have time to make sure that the rifle scope stays in place and the gun continues to shoot straight. Over time the gun's excessive recoil has a tendency to make the scope bases rings move backwards. I'm hoping that the Permatex Threadlocker Blue Medium material will keep the screws from backing out and letting the scope rings move again.

I'm hoping that this will be a permanent fix and I won't have to go though this again for a long time. But I'm not going to hold my breath based on my past experience with this Gamo Rifle.

Note 2: I spend a few hours on the web today looking for review on this Gamo rifle and the scope. I found that other people had similar experiences with this rifle and scope. That's where I got the idea on using the extra Gamo scope stop.

[Moveon]

I think that the rifle is working now. After installing the new scope stop behind the back rings the scope has not moved anymore. I maked the receiver with a awl and can see if the back ring has moved from it's original position and it's not moving any at all.

I got a Wheeler Engineering Fat Wrench which is a small hand held torque wrench that works really good. I had to buy a insert screw to fit the head on my ring's screws but other than that it was easy to use and work with. The Fat Wrench that is. I also have a Wheeler Engineering Profession Scope Installation kit now in case I have to mount any more rifle scopes. I can now lap the rings to fit a 1" scope and have the tools to measure the fit when done. This ensures that the rings and scope body match up perfectly together. I found that it's critical to do that for long range shooting accuracy.

I've invested in a new AR15 with a new Nikon Scope and an EOTech Hollow Graphic Weapons Site system.

I still have the Gamo Bone Collector Air Rifle and have used it to dispatch the Fox Squirrels from my Bird Feeders. The last Fox Squirrel that got into my Sunflower Seed Feeder tray got blasted off the platform from 10 ft away and I hit him right between the eyes. So the Gamo Rifle and Scope is deadly accurate now and doing the job that I bought it for. I either live trap these Fox Squirrels if possible and transport them to another area far away or shoot them if I can't trap them live. Either way they are removed and not eating me out of house and home. That bird seed is not cheap and one Fox Squirrel can eat as much bird seed in one sitting as ten Blue jays.

There are still plenty of Fox Squirrels around as I see them running around in my neighbor's yards so they will eventually figure out where my bird feeders are and I'll have to trap them or shoot them. They seem to replace themselves with new young squirrels every year so I don't think that I'll run out of targets any time soon.

They mate is Jan and have their young in the spring of the year and produce 4 to 6 little squirrels each year. But the next winter the little one's are ready to breed. They get in one of my trees and since it's got a lot of leaves growing all over the tree it's very hard to see them when they get up in that tree. So I really can't shoot them out of the tree and have to wait until they get in another tree that's more open.

I'm just happy that I got the Gamo working right as I paid a little over $200 for that air rifle just to be able to shoot the squirrels. I have two other Crosman 1077 Repeating Air Rifles that I loved until the seals went bad and they would not hold the CO2 in the Cartridges. Which made them useless to me. I'd have them fixed but it cost more to fix them than to buy a new one. And I don't need a new one that will go bad in a few months time. Then I'd be stuck with three useless air guns. The only reason I purchased the second one is because I purchased a adaptor for the first one to let me use the larger CO2 containers. But then later I learned that the adaptor for only used for a more modern version of my Crosman 1077 Rifle. The one I had was not able to work with the new adaptor so I figured I'd just buy a new 1077 to work with the new adaptor kit. That new rifle only worked for a short time before it's seals started leaking so bad that it would not hold any air in the system. So don't buy the Crosman 1077 Air Rifle as it' junk. Too bad they can't redesign the seals to make the system work. As if the seals hold the air the rifle is pretty cool. I think that the rotary clip holds either 12 bb's or 12 .177 lead pellets and it's a semi auto. So when it was new and working right I could fire 12 shots before reloading. I took my old 1077 to the gun smith that's a certified Crosman repair dealer and they told me it cost too much to fix them and that it's not worth fixing. So that's not something that I said that's what the guy at RAJO's gun shop said. And he is the local Crosman's Authorized Repair shop in this area.